HomePage Introduction Quality Assurance Market Services Inquiry Online Contact Us
 
PRODUCT INFORMATION
 
 
    Drilling Rig & Rig Parts
    Downhole Tools
    OCTG
    Wellhead Equipment
    Handing Tools & Power Tong
    Featured Products
 
CONTACT US
 
 
Tel: 0086-29-81138812
Fax: 0086-29-81138812
Email:
sales@scotonoilfield.com
scotonbabala@hotmail.com
 
 
 
 
 
 
 
Product Show
Drilling Jar

Mechanical Drilling Jar
BZ mechanical drilling jar is a full mechanical type drilling jar and releasing stuck tool. It integrates upward jarring with downward jarring releases the tight pull or the sticking or other drilling troubles during drilling. It is a part of drill stem when it needn't jarring and it can work at anytime when need jarring. Thus increasing the work effciency. It has widely load ( jarring force) scope of the upward jarring and the downward jarring, so it can be adjusted at the maintenance stations or on the well sites according to the requirements. The special flexible joint can reduce the flexural stress of the drilling jar body effciently. So it is the frst selected drilling jar for vertical well deep well directional well and complicated well operations.
Specifcation:

Model

BZ121

BZ165/159

BZ203/197

OD mm(inch)

121(4 3/4)

165(6 1/2)/159(6 1/4)

203(8)/197(7 3/4)

ID mm(inch)

50.8(2)

57.2(2 1/4)

71.4(2 13/16)

OAL(Locking place) mm(inch)

6370(251)

7015(276)

7310(288)

Upper Stroke mm(inch)

210(8 1/4)

142(5 9/16)

145(5 11/16)

Lower Stroke mm(inch)

197(7 3/4)

172(6 3/4)

178(7)

Conn.

NC38

NC50

6-5/8REG

Max. Tensile Load(MN)

1.4

2.2

2.5

Max. Working Torque(KN·m)

13

15

20

Upward Jarring Force(KN)

450

630

820

Downward Jarring Force(KN)

230

360

460

Pumping Area(cm2)

62

100

174


Hydraulic-mechanical Drilling Jar
YJZ hydraulic-mechanical drilling jar integrates hydraulic principle with mechanical principle, it’s a new type drilling jar, which can suit for all kinds of drilling operations, and go with drilling tools assembly to decont the well when uesd. The drilling tools are often sticked due to many kinds of reasons in down hole when in normal drilling operations, and this type drilling jar is an effective tool for releasing stuck. When the drilling tools are sticked, it can make drilling jar generate upward or downward jarring force through lifting and landing the drill strings, so it can release resistance and the stick by many time jarring, and recover normal drilling operation promptly. Meanwhile avoid resistance and stick to become further accident, and cause larger economic losses. If releasing force is failed, it can dynamiclly adjust at anytime on sites and be easy to use.

Specifcation:

Model

OD                  mm(inch)

ID              mm(inch)

Conn.

Max.              Tensile            Load(KN)

Max.          Working   Torque                (KN·m)

Rated Force

Upward   Jarring Force      (KN)

Downward      Jarring Force      (KN)

YJZ121

121(4 3/4)

44.5(1 3/4)

NC38

1000

12

400±30

220±30

YJZ165

165(6 1/2)

57.2(2 1/4)

NC50

1500

14

650±30

300±30

YJZ203

203(8)

70(2 3/4)

6 5/8REG

2200

18

800±30

400±30


Hydraulic Drilling Jar
QYZ hydraulic drilling jar integrates upward jarring with downward jarring, It is a hydraulic type drilling jar .which is used in all kirds of well conditicn, it generates up and down jarring force by lifting and releasing drill stems when the drilling tools were stuck and make sure drilling operation can go smoothly. This type drilling jar has some advantages like easy operation stable property safety and reliability maintenance etc.

Specifcation:

Model

OD                  mm(inch)

ID              mm(inch)

Full Open     Stroke     mm(inch)

Conn.

Max.          Working                 Load            (KN)

Max.              Tensile            Load (KN)

Max.          Working   Torque                (KN·m)

QYZ121

121(4 3/4)

57(2 1/4)

635(25)

NC38

350

1364

18

QYZ165

165(6 1/2)

69(2 23/32)

635(25)

NC50

770

2668

55

QYZ203

203(8)

76(3)

635(25)

6 5/8REG

1300

4700

106


Super Fishing Jar
CSZ Super fshing jar is an advanced fshing and jarring tool, which applies hydraulic and mechanical principle, adopts for advanced  technology and concentrates advantages of all kinds of fshing and jarring  tools. It has compact structure, reliable property, convenient  to adjust, easy use. It  is a new  type upward jarring tool used in petroleum and geological explorations.

Specifcation:

Model

OD                  mm(inch)

ID              mm(inch)

Conn.

Max.    Stroke    mm(inch)

Sealing    Pressure   (MPa)

Max. 

Working 

Torque

(KN·m)

Max.  Jarring Lifting Tons

(KN)

Max.      Tensile   Load      (KN)

Closed Length  mm(inch)

CSZ46

121(4 3/4)

50.8(2)

NC38

305(12)

20

9.8

350

900

3883(153)

CSZ62

159(6 1/4)

57.2(2 1/4)

NC50

321(12 5/8)

20

12.7

700

1500

3976(156 1/2)

CSZ64

165(6 1/2)

57.2(2 1/4)

NC50

321(12 5/8)

20

13.7

700

1550

3976(156 1/2)

CSZ70

178(7)

60(2 5/16)

5 1/, 2FH

305(12)

20

14.7

800

1800

3986(157)

CSZ76

197(7 3/4)

76.2(3)

6 5/8REG

328(13)

20

19.6

1000

2100

4329(170)

CSZ80

203(8)

76.2(3)

6 5/8REG

328(13)

20

19.6

1200

2200

4329(170)


Hydraulic Jar Intensifer
YJS hydraulic jar intensifer is a kind of down hole fshing jar tool designed to increase jarring function for up jar. So it must be used together with super fshing jar. It could accelerate for the top end of jar and the drill collar connecting with its bottom end when working, so to get larger jarring force on stuck point, and reduce quake of drill stem springback after jarring at the same time.

Specifcation:

Model

OD                  mm(inch)

ID              mm(inch)

Stroke    mm(inch)

Max. Tensile Load in Down Hole   (KN)

Sealing Pressure  (MPa)

Max. Working  Temperature

()

Conn.

Overall  Length   mm(inch)

YJS46

121(4 3/4)

38(1 1/2)

224(8 3/4)

0.9

20

120

NC38

3275(129)

YJS62

159(6 1/4)

57.2(2 1/4)

329(13)

1.5

20

120

, NC50

4380(172)

YJS64

165(6 1/2)

57.2(2 1/4)

329(13)

1.5

20

120

NC50

4380(172)

YJS70

178(7)

60(2 5/16)

336(13 1/4)

1.8

20

120

5 1/2FH

3740(147)

YJS76

197(7 3/4)

76.2(3)

333(13 1/8)

2.1

20

120

6 5/8REG

4238(167)

YJS80

203(8)

76., 2(, , 3)

333(13 1/8)

2.2

20

120

6 5/8REG

4238(167)


Surface Bumper Jar
DXZ Surface bumper  jar  is a  tool releasing stuck for down hole tools on the wellhead, It applys to release stuck which needs downward jarring like keyslot, shrink neck, fall off block, sticking  to suck etc.  it also can relieve down hole fishing tools. When surface bumper jar is working on wellhead. No matter what parts of drill stems stuck, slips down hole tools stuck, fshing tools stuck or testing workover tools, well washing tools stuck, it all can use surface bumper jar to release stuck.DXZ Surface bumper jar is a new type full mechanical surface bumper jar, it overcomes previous defect of friction type's slips are easy to burn. adjusting is not exact, it can adjust jarring release force at any time, and easy exact stable to adjust.

Specifcation:

Model

DXZ178-1

OD

mm(inch)

178(7)

ID

mm(inch)

57.2(2 1/4)

Allowed Max. Releasing Force

KN

800

Ex-Factory Calibrate Releasing Force

KN

380~420

Max. Tensile Load

KN

1800

Max. Working Torque

KN·m

15

Sealing Pressure

MPa

20

Conn.

API

NC50

Length

mm(inch)

4200(165)

Working Temperature

-40~120


Fishing Bumper Sub
KXZ Fishing bumper sub is a mechanical jarring tool. It can repeatedly jar for stuck drill stem, make stuck point loose and release, when lifting and jarring can not release stuck, it still can rotate to make releasing fshing tools release fshes. When fshing bumper sub works with mechanical  internal cutter,  it can make  internal cutter get preset constant forward force, to cut steadily. When it works with back off tools, it can compensate a rising stroke for connection after back off.

Specifcation:

Model

Outside Dimension mm

(inch)

Conn.

Tensile Load

(KN)

Stroke  mm

(inch)

ID    mm

(inch)

Max. Working Stroke  (KN·m)

Make Up Torque 

(KN·m)

KXZ121

φ121×2102(4 3/4×82 3/4)

NC38

1220

1000(37 3/8)

38(1 1/2)

8

9

KXZ159

φ159×2606(6 1/4×102 1/2)

NC50

1330

1400(55)

50.8(2)

13

16

KXZ165

φ165×2606(6 1/4×102 1/2)

NC50

1430

1400(55)

50.8(2)

13

16

KXZ171

φ171×2606(6 3/4×102 1/2)

NC50

1530

1400(55)

50.8(2)

13

16

KXZ178<, o:p>

φ178×2606(7×102 1/2)

NC50

1530

1400(55)

50.8(2)

15

16

KXZ203

φ203×2729(8×102 1/2)

6 5/8REG

1800

1500(59)

70(2 3/4)

20

20


Mechanical Shock Absorber
JQ-DH shock absorber  is an absorbing  tool acting as vertical absorbing function when drilling with cone bits or abrasive coring bits. It can absorb or slow down vertical shocking and impact load of drill stem when drilling, thereby keep normal drilling pressure, prolong working life of drill bit, protect drilling tools and surface equipments, decrease drilling cost, increase drilling effciency. JQ-DH uses butterfy spring as elastic element,  it is different from hydraulic shock abscrber using silicon oil and other fluid as working medium, its working property doesn't be effected by working environment, this mechanical  type shock absorber is a new R&D tool made by our factory and a foreign company, it has the advantages of simple structure, reliable working, convenient operation and maintenance, good absorbing effect, long working life and high property, it’s one of the most widely used drilling tools oversea.

Specifcation:

Model

JQ-DH178

OD

mm(inch)

178(7)

ID

mm(inch)

57(2 1/4)

Max.Stroke

mm(inch)

50(2)

Max.Working Pressure

KN

350

Max. Working Torque

KN·m

15

Max. Working Pull

KN

1500

Max. Length

mm(inch)

2570(101 3/16)

Conn.

API

NC50

Working Temperature

-40~150


Hydraulic Shock Absorber
JQ-Y hydraulic shock absorber can use it’s inner compressible liquid to absorb or reduce impact and shock load on drill bits and drilling tools in drilling operations, protect drill bit teeth, bearing and drilling tools, prolong working life of drill bits and drilling tools.

Specifcation:

Model

JQ-Y121(4-3/4)

JQ-Y159(6-1/4)

JQ-Y165(6-1/2)

JQ-Y203(8)

JQ-Y229(9)

OD mm(inch)

121(4-3/4)

159(6-1/4)

165(6-1/2)

203(8)

229(9)

ID mm(inch)

35(1 3/8)

50.8(2)

50.8(2)

68(2 5/8)

75(2 15/16)

Conn.

3-1/2REG

4-1/2REG

NC50

6-5/8REG

7-5/8REG

Max. Stroke  mm(inch)

100(3 15/16)

120(4 3/4)

120(4 3/4)

140(5 1/2)

140(5 1/2)

Max. Working Load (KN)

265(27.02)

333(33.96)

333(33.98)

480(48.95)

529(539.5)

Tensile Yield Strength (KN)

≥2100(214.15)

≥2200(224.35)

≥2200(224.35)

≥6600(673.06)

≥6600(673.06)

Torsion Yield Strength (KN·m)

≥40(4079.14)

,

≥60(6118.7)

≥60(6118.7)

≥270(27534.16)

≥270(27534.16)

Elastic Rigidity (KN/mm)

3.6(367.12)

4.8(489.5)

4.8(489.5)

5.5(560.88)

6.5(662.86)

Max. Working Temperature ()

200

200

200

150

150



 
 
Copyright©2015 Scoton Oilfield All Right Reserved